Dragonfly Pendant Necklace
By: Designed by Jana Ewy for AMACO
A colorful background created with friendly plastic offsets a lovely brass dragonfly in this jewelry craft project. Try using different color combinations to create your very own unique look.
- Friendly Plastic 7” sticks: colors of your choice
- Mat knife
- Acrylic ruler
- Cutting mat
- Craft knife
- Needle tool
- Rectangle shaped cutter:
- Small dish of cold water with a few drops of olive oil
- Griddle set at 200-300 degrees
- Non-stick baking sheet that fits flat on griddle surface
- Heat tool
- Sealer: I used Envirotex Lite, but any high gloss acrylic sealer will work.
- Disposable mixing container and stir stick
- Non-stick cookie sheet
- Round nose and needle nose jewelry pliers
- Vintaj brass diamond filigree connector, folded in half.
- Vintaj brass 32mm rectangle blank
- Vintaj brass tiny dragonfly
- E6ooo glue
- 2 AB crystal rhinestones
- Jewelry findings: brass chain, clasp, and jump rings
- Fracture: Using a cutting mat, ruler and blade, cut the plastic sticks into 1/4” strips. Then cut the strips in half using a scissor.
- Fusion: Pre heat the griddle. Place the baking sheet onto the griddle. One at a time, in a pleasing color pattern, place the plastic strips onto the baking sheet. Make sure each strip is stuck in place before adding the next. Try to press each strip tightly against the one before, to prevent any gaps. Continue until all of the strips have been added, 3 to 4 inches. Allow the plastic to soften and fuse together. If any gaps do appear, simply tap over them with your finger pressing the softened plastic together. When all the strips have softened and sealed together, remove the baking sheet from the griddle and allow the plastic to cool. Use the needle tool to press under the edges of the cooled plastic and remove it from the pan.
- Fracture: Place the cooled plastic back on the cutting mat and trim off the two uneven edges. Continue to cut the plastic into random widths, from about 1/4” to 1/8”until the entire piece has been cut apart.
- Flip every other strip in reverse, revealing what the finished fractured pattern will look like. Play around with the different size strips until you have the desired pattern. The finished piece only needs to be larger enough to accommodate the rectangle cut-outs.
- Fusion: Place the baking sheet back onto the griddle. One at a time, in the pattern you have arranged, place the plastic strips onto the baking sheet. Make sure each strip is stuck in place before adding the next strip. Try to press each strip tightly against the one before, to prevent any gaps. Continue until all of the strips have been added. Allow the plastic to soften and fuse together. If any gaps do appear, remember to tap over them with your finger pressing the softened plastic together. When all the strips have softened and sealed together, remove the baking sheet from the griddle.
- While the plastic is still warm, cut the rectangle by pressing the cutter into the softened plastic. Dip the cutter back into the cold water after each cut if you are making more than one pendant. This will help keep it from sticking to the plastic. Allow the plastic to cool. You may place the pan under cold running water to speed the cooling process along. Use the needle tool to press under the edges of the cooled plastic and remove it from the pan. Pop out the rectangle. If needed use the craft knife to cut around it.
- Mix the Envirotex lite sealer following the manufactures instructions. Application: I like to place my pieces on a non stick cookie sheet. This way if there is any run off, it will be easy to remove later. Once I have the Envirotex mixed, I like to pour it into a small squeeze bottle. The application will be more precise and much easier. Once the resin has been applied, blow softly through a straw over each piece to pop any bubbles that remain. Allow the pieces to dry at least 12 hours. If there has been any run off. Remove the piece from the pan by pressing the needle tool under it and lifting. The resin is still soft enough that you can cut the excess off with a scissor. Envirotex cures completely in 24 hours.
- Position and glue the friendly plastic rectangle into place on the brass blank. Position and adhere the dragonfly and rhinestones onto the plastic. Allow the glue to dry.
- Using the round nose pliers fold the brass filigree diamond in half, creating a bail. Attach the filigree bail to the pendant using a jump ring. Assemble the necklace and slid the pendant onto the chain.